Hobart-welding-products 1025 Manuel d'utilisateur

And Non-CE ModelsCybercut 1025ProcessesDescriptionAir Plasma Cuttingand GougingAir Plasma CutterOM-2210 176 876KMarch 1999Visit our website atwww.Hoba

OM-2210 Page 6D N’approchez pas le tube du chalumeau et l’arc pilote lorsque la gâchette estenfoncée.D Le câble de masse doit être pincé correctement

OM-2210 Page 71-3. Dangers supplémentaires en relation avec l’installation, le fonctionnement et la maintenanceDES PIECES CHAUDES peuvent pro-voquer d

OM-2210 Page 81-5. Information sur les champs électromagnétiquesDonnées sur le soudage électrique et sur les effets, pour l’organisme,des champs magné

OM-2210 Page 9SECTION 2 − DEFINITIONS2-1. Warning Label DefinitionsWarning! Watch Out! There arepossible hazards as shown by thesymbols.1 Cutting spar

OM-2210 Page 101 Warning! Watch Out! Thereare possible hazards asshown by the symbols.2 Incorrect voltage will damageunit.3 Read Owner’s Manual.4 Look

OM-2210 Page 11SECTION 3 − INSTALLATION3-1. Specifications For Units Connected to a 20 Ampere, 115 Volt Circuit or a 10 Ampere,230 Volt CircuitAmperes

OM-2210 Page 123-4. Duty Cycle And Overheating For Non-CE ModelDuty Cycle is percentage of 10 min-utes that unit can cut at rated loadwithout overheat

OM-2210 Page 1318 in(457 mm)3-6. Selecting A Locationloc_2 3/96 - ST-801 303-B / ST-801 319-B1 Lifting HandleUse handle to lift unit.2 Hand CartUse ca

OM-2210 Page 143-7. Connecting Work Clamp And Gas/Air SupplyRef. ST-091 547-C / Ref. ST-801 306-B1 Work Clamp2 WorkpieceConnect work clamp to a clean,

OM-2210 Page 153-8. Setting Input Voltage Selector Switch And Connecting Input Power ST-801 304-B / ST-801 319-BCheck input voltage available at site.

OM-2210 Page 16SECTION 4 − OPERATION4-1. ControlsRef. ST-801 306-B / Ref. SC-192 4921 Output ControlUse control to set cutting output.The yellow zone

OM-2210 Page 174-2. Cutting SpeedThe cutting speed curves show therecommended maximum cuttingspeed capabilities of the powersource and torch for mild

OM-2210 Page 184-3. Sequence Of OperationPress trigger. Pilot arc starts.After cutting arc starts, slowlystart moving torch across metal.Adjust torch

OM-2210 Page 19SECTION 5 − MAINTENANCE & TROUBLESHOOTING5-1. Routine MaintenanceY Disconnect power before maintaining.. Maintain more oftenduring

OM-2210 Page 205-2. Overload Protection: Trouble Lights & Checking Shield Cup Shutdown SystemIf certain problems occur, theReady light goes off, a

OM-2210 Page 215-3. Torch And Work Cable ConnectionsIf torch or work cable needs to beremoved or replaced, proceed asfollows:Turn power Off, and disco

OM-2210 Page 225-4. TroubleshootingTrouble RemedyNo pilot arc; difficulty in establishing anarc.Clean or replace worn consumables as necessary (see to

OM-2210 Page 23SECTION 6 − ELECTRICAL DIAGRAMFigure 6-1. Circuit Diagram For Power SourceSC-189 005

OM-2210 Page 24SECTION 7 − PARTS LISTFigure 7-1. Main Assembly. Hardware is common andnot available unless listed.ST-801 412-E124567891011312131416171

OM-2210 Page 25DescriptionPartNo.ItemNo.Figure 7-1. Main AssemblyQuantityDia.Mkgs.1 183 161 COVER, top 1. . . . . . . . . . . . . . . . . . . . . .

TABLE OF CONTENTSSECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING 1. . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1. Symbol Usage 1. . . .

OM-2210 Page 26DescriptionPartNo.ItemNo.Figure 7-1. Main Assembly (Continued)QuantityDia.Mkgs.38 FRONT PANEL, (consisting of) 1. . . . . . . . . . .

Effective January 1, 1997This limited warranty supersedes all previous manufacturerswarranties and is exclusive with no other guarantees orwarranties

PRINTED IN USAModel Name Serial/Style NumberPurchase Date (Date which equipment was delivered to original customer.)DistributorAddressCityState ZipPle

dec_con1 1/96Declaration of Conformity forEuropean Community (CE) ProductsThis information is provided for units with CE certification (see rating lab

OM-2210 Page 1SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USINGpom _nd_5/971-1. Symbol UsageMeans Warning! Watch Out! There are possible hazardswith

OM-2210 Page 2Sparks and hot metal blow out from the cutting arc.Chipping and grinding cause flying metal.FLYING SPARKS can cause injury.D Wear approv

OM-2210 Page 31-3. Additional Symbols For Installation, Operation, And MaintenanceHOT PARTS can cause severe burns.D Do not touch hot parts bare hande

OM-2210 Page 41-5. EMF InformationConsiderations About Welding Or Cutting And The Effects Of LowFrequency Electric And Magnetic FieldsWelding or cutti

OM-2210 Page 5SECTION 1 − CONSIGNES DE SÉCURITÉ − LIRE AVANT UTILISATIONpom_nd_fre_5/971-1. Signification des symbolesSignifie Mise en garde ! Soyez